Heavy-duty trucks, farm equipment and construction machinery all expose the same thing to a technician or a fleet device: a diagnostic port. Telematics units, data loggers and test tools have to share that port with equipment already on the vehicle, and the cable you pick decides whether that goes smoothly.
Here we cover the connector families you will meet on heavy vehicles (J1939, J1708 and OBD II J1962) and a few parts from our Machinery and Transportation cable line.
The three interfaces in plain terms
- J1939: we have built an extensive family of tooling around SAE J1939 using Deutsch 9-pin circular connectors.
- J1708: our J1708 tooling covers SAE J1708 and J1939 with Deutsch 6- and 9-pin circular connectors.
- J1962 (OBD II): our OBD II cables are designed to be fully compatible with the SAE J1962 CAN standard, for 12 or 24 volt systems, with standard tooling or something unique to your application.
Pass-through, splitter or blunt cut?
Pass-through cables
A male-to-female pass-through plugs between the vehicle and its existing connector. The fly-away leads on the other end let your device tap the bus without breaking the original connection.
Splitter and Y cables
When the port is already in use, a splitter turns one connection into two. We list J1939 Type 1 and Type 2 splitters, a Type 2 to Type 1 and 2 splitter, and OBD II pass-through versions.
Blunt-cut tails
If you are building your own telematics module, a connector with a blunt-cut end gives you a ready-made vehicle interface to terminate in your design, available with 9 or 16 conductors.
Recommended heavy vehicle and OBD II cables
Each product page lists the details for that part. Some parts carry a minimum order quantity, noted on the page, so check before you plan a build.
J1939 Type 1 Splitter Cable, 9 Pin Male to 2 X 9 Pin Female
Part # 11760-03-308
Splits one Deutsch-style 9-pin J1939 connection into two 9-pin female outputs, so a logger or telematics unit can share the port with existing equipment.
Deutsch J1939 Pass Through M-F, 6 ft. to Fly Away Leads
Part # 11760-03-235
A 6 ft male-to-female J1939 pass-through with fly-away leads, for tapping the bus while leaving the vehicle connection intact.
J1708 Pass Through M-F, 6 ft to Fly Away Leads
Part # 11760-03-135
The same pass-through approach for J1708 on heavy vehicles, with a 6 ft run to fly-away leads.
Deutsch 9-pin Male to Female with DB15 Male
Part # 11760-03-250
Deutsch 9-pin male and female ends plus a DB15 male, for bringing J1939 data to a DB15 port.
OBD II J1962 Cable Male Right Angle to Blunt End Cut, 16C x 24 AWG
Part # 11760-03-302
J1962 male right-angle connector with a blunt-cut 16-conductor, 24 AWG tail for your own termination. A 9-conductor version is 11760-03-302-09.
OBDII Passthrough Male to 2 Females
Part # 11760-03-318-02
OBD II pass-through that lets two devices share a single J1962 diagnostic port.
Heavy vehicle cable selection checklist
- Confirm which protocol the vehicle uses: J1939, J1708 or OBD II J1962.
- Check the connector: Deutsch 9-pin, Deutsch 6-pin or J1962, and whether you need a right-angle plug.
- Decide if your device must share the port (pass-through or splitter) or own it.
- Specify the length and termination: fly-away leads, blunt cut, or DB15.
- Confirm 12 V or 24 V operation.
- Check the minimum order quantity on the product page.
Need a different configuration?
Our standard configurations usually cover most OEM requirements. If yours needs something else, we will build it to your application. See our Deutsch connector harness page, browse the online shop, fill out the RFQ form, or email onlinesales.ocp@us.interplex.com.











